Description
Keep the base. Change the module.
Cove Hub is a compact desk organizer with a lift-out phone stand, a divided pen/tool cup, a long front tray and a separate small-device pocket. The everyday setup works without buying a wireless charger. A second, optional insert replaces the phone stand when a matching charging puck is available.
WHY THESE FEATURES
Public user discussions repeatedly mention tangled cables, charger pucks that pull out with the phone, changing puck dimensions and interference with camera bumps. This design responds with accessible cable routing, replaceable modules, a fit-test coupon and a charging face raised above the surrounding printed ring. It does not claim to solve magnetic retention or to fit every phone or charger.
EVERYDAY SETUP
- Base footprint: 174 x 174 mm, height 15 mm. Nominal floor 3 mm.
- Lift-out phone module: 87.4 x 109.4 x 88 mm. The back support is approximately 17 degrees from vertical. Two raised seats leave a 25 mm central cable opening. The bottom of the reference phone sits 33 mm above the desk; usable connector space above the insert floor is approximately 27 mm before allowing for cable bend radius.
- A generic 76 x 158 x 11 mm phone envelope was checked in CAD in portrait orientation without an intersection. This is not a tested device-compatibility claim. Landscape use and larger cases must be checked on the physical prototype. No tablet-load claim.
- Three rear open cable grooves have nominal widths 4, 5 and 6 mm. These are guides, not strain-relief clamps.
- Front storage pocket: nominal 158 x 40 x 12 mm with rounded corners. Measure folded glasses or other items before relying on the fit.
- Right storage pocket: nominal 64 x 64 x 12 mm with rounded corners; intended for small earbud cases or everyday items.
- Divided cup: 63.4 x 39.4 x 58 mm. Two compartments for pens and small tools, with finger access.
- Inserts sit in their pockets under gravity, with 0.3 mm nominal clearance on each side. They are removable, not latched or positively locked.
- Four underside recesses accept optional 10 mm adhesive silicone feet, approximately 0.8 mm recessed. Feet are not included.
OPTIONAL WIRELESS INSERT — MEASURE BEFORE PRINTING
This is a passive holder, not a charger. It is sized around the published Apple A2140 envelope: diameter 55.9 mm, thickness 5.3 mm. The supplied socket is 56.2 mm in diameter; the nominal puck face stands 3.8 mm above the ring. The central opening and underside channels give access beneath the puck, but no cooling or charging-performance benefit has been measured. Cable access is open from above with an 8 mm passage. Do not force or sharply bend the lead.
Print the small 56.2 mm fit coupon first. This is a clearance-fit horizontal seat, not a magnetic-release clamp: the puck may lift with the phone. Hold the puck/insert when removing the phone. Do not assume one-handed removal or compatibility with later generations, other brands, thick cases or every camera bump. The charger, USB power adapter and cable are separate purchases. Use the charger intact, follow its manufacturer's instructions and keep metal objects out of the charging area. No electronics are enclosed in the base.
PRINTING — UNTESTED STARTING POINT
Print the parts separately in their supplied flat-base orientation. Start with a 0.4 mm nozzle, 0.20 mm layers, 3 walls, 5 top/bottom layers and 15-20% infill. Use the printer manufacturer's material profile. PETG is suggested for the optional charger insert; ordinary room-temperature, non-charging pieces can be evaluated in PLA or PETG. Thermal suitability still needs a real test.
Base and cup have open-top cavities. The phone module has underside ledges and openings; enable supports where the slicer preview shows unsupported regions, especially the connector opening and back slots. The optional insert has short underside channel bridges that need slicer review. Do not treat this as a verified support-free model. The 174 mm base leaves little margin on a nominal 180 mm bed; check printable area and brim requirements. Do not scale the model globally to make it fit: this changes the mating clearances and charger fit.
ASSEMBLY
1. Print the base, phone module and divided cup for the basic setup.
2. Remove supports and clean any elephant-foot edges. Dry-fit the inserts gently; do not force them.
3. Seat the phone module in the large left pocket and the cup in the rear-right pocket.
4. Route your USB lead through the front central opening; leave enough slack for the connector and bend radius. Test phone fit, stability and cable access before regular use.
5. To use the optional charger insert, first measure the puck and test the coupon. Replace the whole phone module with the charging insert. The two modules are alternatives, not stacked parts.
VALIDATION AND STATUS
All five exported STLs were reloaded and checked for watertightness and consistent winding; each part is a single connected solid. Assembly checks found no volumetric intersections between the base and its inserts. CAD checks also found no intersections with the stated reference phone envelope or charger envelope. These are geometry checks only. No part has been physically printed, sliced, thermally tested or load-tested. All pictures are CAD renders; the phone is a dimensional reference prop and is not supplied. Physical fit, grip, stability, charging and long-term durability remain unverified.
AI DISCLOSURE
An AI assistant developed the concept, CAD code, geometry, renderings and draft documentation at the entrant's request. Research informed the requirements; no third-party model files were copied or remixed. The participant does not claim manual CAD authorship or physical testing.
REFERENCE
Charger dimensional drawing: https://developer.apple.com/download/files/accessories/dimensional-drawings/apple-magsafe-charger.pdf
Apple and MagSafe are trademarks of Apple Inc. They identify the dimensional reference only; this independent prototype is not endorsed or certified by Apple.
This model is licensed under
Creative Commons Attribution-NonCommercial-NoDerivs
Cove Hub — Modular Desk Organizer & Phone Stand Entered in Desk Organizers & Stands
Print Profiles
+Show Print ProfilesDiscussed in
Similar models
desk organizer • phone stand • cable guide
Desk Harbor — Phone Rest, Catch-All Tray & 3 Cable Guides
Galaxy A16 • Samsung • Android
Cove Wall Phone Holder for Galaxy A16 5G | Open-Front Charging Pocket | Screw Mount
phone stand • desk organizer • desk tray
Case-Friendly Phone Stand & Desk Tray — Fits Phones in Cases up to 84 mm Wide, No Supports
DeskOrganizersChallenge • CallCove • desk organizer
Comments2