Description
One clamp on the desk edge does three jobs: headphones hang on the arch above the desk, a bag or backpack on the hook below it, and two cables through the fixed jaw. It grips desk tops from 12 to 45 mm thick, and the screw is turned by hand - no tools, nothing screwed into the desk.
Three printed parts. The CLAMP BODY carries the fixed jaw, the headphone arch, the bag hook, two cable slots and a 15 mm nut boss. The SCREW BOLT runs through that boss on a Tr12 x 6 buttress thread. The SWIVEL PAD clips onto the bolt head, turns with the screw and tilts on a 45 degree seat, so it presses flat on the desk instead of dragging on it while you tighten.
Sizes: desk tops 12-45 mm; mouth 62 mm deep and 52 mm wide, with 26 mm of clear space behind the screw; screw 12 mm major diameter, 6 mm pitch, 8.4 mm root, 45 degree trailing flank; nut engagement 15 mm (2.5 turns) with 33 mm of travel; knob 40 mm across with 30 grip flutes; swivel pad 34 x 34 x 6 mm; two 8 mm cable slots through the fixed jaw; assembled 108 x 52 x 161 mm.
Printing: one 3MF inside the ZIP, all three parts already in the orientation they print in, and none of them needs supports - the body lies on its side so every wall is vertical, the bolt stands on its knob, the pad sits pocket-down. 0.2 mm layers, 4 perimeters, 5 top and 4 bottom layers, 25-30 % gyroid, PETG (PLA+ works too). Do not scale the file: the 0.40 mm radial and 0.30 mm axial thread clearance is modelled in and a 2 % shrink closes the thread until it binds. Plate 156 x 161 x 74 mm, roughly 75-90 g of filament.
Checked on the delivered mesh, not on the CAD: all three parts are closed 2-manifold solids with 0 non-manifold edges, 0 degenerate facets, one body each and positive volume; 47 cm2 of bed contact on the body, 11 cm2 on the bolt, 10 cm2 on the pad; measured radial thread clearance 0.40 mm; pad snap interference 0.23 mm; no face overhangs more than 45 degrees except facets inside the 9 mm thread bore, and the largest single unsupported face is 10 mm2.
Assembly: press the pad onto the bolt head until the lip clicks over the mushroom, screw the bolt up through the lower jaw until the thread shows in the mouth, slide the clamp over the desk edge and tighten by hand. Then headband on the arch, a strap loop over the hook, a cable through either slot.
One honest limit: this is a desk accessory, not a lifting point - one pair of headphones and a light bag of a few kilos is what it was drawn for; on a hollow-core panel, clamp it near an edge or over a solid part of the top. Design: parametric Python CAD (shapely outlines, manifold3d booleans, a helical thread generator), rendered with a numpy renderer written for this project; AI assistance was used throughout. Licence CC BY-NC-SA 4.0.
This model is licensed under
Creative Commons Attribution-NonCommercial-ShareAlike
Desk C-Clamp Hook for Headphones, Bags & Cables (12-45 mm Desks) Entered in Tools & Functional Prints
Print Profiles
+Show Print ProfilesDiscussed in
Similar models
phone stand • desk organizer • desk tray
Case-Friendly Phone Stand & Desk Tray — Fits Phones in Cases up to 84 mm Wide, No Supports
USB-C hub • hub stand • hub holder
Port Ventilated USB-C Hub Stand | Strap-Mount Hub Bridge | Desk Cable Management
tool holder • hex bit organizer • screwdriver stand
Modular Hex Bit & Driver Desktop Tool Rack (18 × 1/4" bits, No Supports)
Galaxy Z Fold6 • foldable • Samsung
Comments